UK manufacturer and supplier of quality copper terminals, busbars, earth bars, coils, heat sinks and braids to the electrical industry.

01249 810000


Riker CAT 5000 The portable injection tester, 5KA

Precisely calibrated protection means enhanced traction supply, better revenues and ROI. Portability means huge cost savings from in-situ calibration and testing. Fully portable 5kA direct current injection for testing and calibration.

The hand-portable CAT 5000 is a new concept in DC circuit breaker calibration that brings rigorous control to traction power with simple, safe, low-cost procedures. Circuit breakers can be rapidly and simply tested on-site in complete safety and minimum disruption to operations. Direct injection testing provides the calibration that removes the risk of nuisance tripping or cumulative thermal overload damage. Railway revenue is directly related to the train capacity provided by traction power. It is vital for any operator to know the reliable capacity of his railway during peak demand and Riker’s CAT 5000 provides safe simple calibration that ensures maximum network capacity under any conditions. This simple process can release up to 70% more power into a network and effectively double the capacity for running trains. Power system calibration is critical to railway network management and the CAT 5000 has brought precision, simplicity and safety into what was once a difficult, expensive and dangerous process. This is why London Underground, Network Rail, Manchester Metrolink and many more companies have recognised the value of calibration and use the CAT 5000 to install, test and maintain their DC traction supply protection.

Portable Injection Tester, 5kA High Current Injectors, Injection Testing Testing and calibrating the direct-acting trip is arguably the most important safety test for circuit breakers. This particularly applies to the heavy-duty breakers used in railway traction but has equal importance elsewhere. Riker’s injection testing equipment operates on a very simple principle: Controlled current sources inject a current that increases steadily (under linear ramp control) until the circuit breaker trips out. The actual trip current of the breaker is then displayed on the control panel and enables breakers to be adjusted and calibrated at a precise safety trip point. Without calibration, a 20% uncertainty in trip point is typical for traction supply protection so that a breaker must be set 20% below maximum safe current. Operating current must be held a further 20% below this if the risk of nuisance tripping is to be avoided. The net result is that, without testing and calibration, a traction supply can only be considered safe and reliable at or below 60% of its designed maximum safe output. This represents a considerable shortcoming on the power and revenue capacity available from a substantial infrastructure investment. Calibrated accurately, on the other hand, a breaker can be set to deliver 100% of a traction supply’s safe output and, typically, trip within 10A on a 7kA supply. In fact, correct adjustment and calibration can enable two trains to run concurrently on sections of track previously limited to one. Accurately calibrating the supply protection also ensures that cabling and connectors used in the traction supply do not suffer from the thermal effects of mechanical cycling and enhanced degradation if safe current levels are repetitively exceeded. Beyond the simple overload protection or emergency isolation there are, therefore, sound economic reasons for maintaining accurate calibration of the direct-acting trip.

Riker pioneered portable high current injectors with the modular 10kA BRECAT supplied to London Underground in 1996. Based on the efficiency of high frequency power conversion, the mass of the equipment is minimised to accommodate the thermal characteristics of a controlled test cycle. This enables lightweight equipment to replace the bulk of traditional fixed installations weighing several tons. Progressive development of the concept has now resulted in the CAT 5000, a 5kA module weighing less than 25kg and housed in a rugged and weatherproof plastic case. The CAT 5000 has now evolved into the definitive test apparatus for railway circuit breakers and guarantees precisely calibrated direct action tripping. The real advantage for railway networks comes from its mobility; systems can be readily transported in a small car or van and hand-carried into a substation or workshop.

Being current sources, output can be simply multiplied by parallel operation. The standard hand-held controller enables up to 20kA to be provided from 1-4 units. This spans the normal current range encountered from light railways through to heavier duties, traction rectifier equipment etc. With one unit or a multiple system, the Riker CAT 5000 provides a powerful and dependable tool for vital railway maintenance



This website is Copyright © 2013-2017 LML Products Ltd. All Rights Reserved.